Home > Easy Driver > Easy Driver Stepper Motor Driver

Easy Driver Stepper Motor Driver

Contents

It’s much easier than I thought it would be. When set LOW, all STEP commands are ignored and all FET functionality is turned off. But there was still a problem! I figured if I used double the rated current to power the motors this would work. news

Ooops. I.e. 4,6, or 8 wire stepper motors. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. language:c //Declare pin functions on Redboard #define stp 2 #define dir 3 #define MS1 4 #define MS2 5 #define EN 6 //Declare variables for functions char user_input; int x; int y; https://www.sparkfun.com/short/10267

Easy Driver Arduino

TP1 allows you to put a meter on the VREF signal as you turn the current adjust pot. SparkFun Recommended Arduino Uno - R3 SMD In stock DEV-11224 This is the new Arduino Uno R3. Caution: Do not connect or disconnect a motor while the driver is energized. Ambient temp in my lab was 70F (21C).

Whichever wire shows the lowest resistance against the first wire is the pair mate. You can either solder directly to the Easy Driver, or use headers for attaching power supplies, motors, etc. First, set it to the lowest setting of the potentiometer. Easy Driver Screwdriver I never do this myself - I adjust the pot until things 'feel' right on my motors since every situation is different.

Feedback? So the higher the M+ voltage, the hotter that regulator will get. I don't know why the pot vendors would choose to make their parts backwards, but that's how it goes. https://www.sparkfun.com/products/retired/13226 Any motor that's rated for 150mA/coil (or more) will work with the Easy Driver just fine, no matter what it's voltage rating.

I’m sure it is probably as good a product as others have reported, but for me, so far, I am not a great fan. Big Easy Driver You might want to do this for power savings reasons. It is stepping down the voltage and stepping up the current. Easy to use about a year ago by Dan199 verified purchaser This is the so easy to use.

Easy Driver Download

Again with everything disconnected, measure the resistance between the four motor output pinsthemselves. click resources shorted) by that little piece of copper on the board. Easy Driver Arduino Purchased Together Break Away Headers - Straight In stock PRT-00116 A row of headers - break to fit. 40 pins that can be cut to any size. Easydriver Stepper Motor Driver Datasheet Most people are perfectly happy running their ED at 12V, and there are tons of power supplies that work great at 12V and are cheap.

There are some additional examples with this library that may be beneficial to you for use with your Easy Driver. navigate to this website When it is received, it’s compared to the four possible functions for the motor, which are triggered from user input. You can read all about it at the Schmalz Haus Big Easy Driver page. Caution: Do not connect or disconnect a motor while the driver is energized. Easy Driver Full Crack

The test setup was as follows: Lab grade power supply powering a v4.4 Easy Driver. A9) There are some mistakes with the EasyDriver silk screen on previous board revs. You should find a sweet spot where the motor doesn’t skip or jerk between steps. More about the author You can NOT trust any sort of power supply current measurement in order to measure the actual coil current at any point in time.

A8) (For Version 3) All nine of the pins on the EasyDriver are on a .100" grid. Easy Driver Software In very close collaboration with SparkFun, I'm happy to release version 4.2 to the world. Code I put together some code you can use to control the stepper with your Arduino.

We use them exte… 1.5 7 Favorited Favorite 31 Wish List Added to your cart!

Do not connect anything else to the ED. The other jumper is labeled APWR on the board and is called SJ1 on the schematic. The way you do that is to cut that little trace in the APWR jumper, thus 'opening' the jumper. A3967slb After running full rotations and near high speed the chip gets extremely hot and the motor starts acting jerky.

Q4) So why does my bench power supply show 12V at 400mA when I know my motor should be drawing 750mA/phase (1.5A total)? The arduino stepper libraries are excellent for controlling connection to 4 wire driver. We're here to help you start something. click site The sleep and enable pins are also broken out for further control.

The variable onerev is set at a constant value of 6400. Mountain Time: (303) 284-0979 Chat With Us sparkfun.com Shop Learn Blog Support Shopping Cart 0 items log in register Shop Learn Blog Support Product Menu Education Forum Data Desktop Site All Facebook Twitter Youtube Google+ Instagram We Accept Amex Discover MasterCard Visa Paypal © 2017 Trossen Robotics × Modal title Ecommerce software by Spark Pay Questions?

It provides much more flexibility and control over your stepper motor, when compared to older versions.The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to The Easy Driver calls those two coils A and B. How much current can you pull from here? SLP - Logic Input.

Gracias. Resources and Going Further Going Further Once you’ve successfully gotten your Easy Driver controlling stepper motors, it’s time to incorporate this into your own project! With everything disconnected from the ED, measure the resistance from each of the four motor output pins to GND and M+. So if you have a small motor, be CAREFUL!

Or perhaps a remote controlled turning art installation? I solder the wires on my stepper motor to a 4-pin .100" male header, and plug that into the breadboard so it connects properly to the EasyDriver.